Bonjour tout le monde !
Bienvenue sur WordPress. Ceci est votre premier article. Modifiez-le ou supprimez-le, puis commencez à écrire !

Tutoriel : connecter une carte SD à un microcontrôleur part 1
Je ne vais pas refaire toute la documentation d’une carte SD mais je vous présente tout de suite comment faire pour connecter une carte SD à un microcontroleur. Les codes sont utilisables directement avec XC8 de Microchip. Cette article portera sur le hardware pour connecter physiquement la carte au micro et sur la partie software.

Isolated DMX splitter
Introduction When you need to connect DMX projectors you can use wireless or cable. In my case, I have a fixed setup so I use a wire solution. But the problem with DMX is the low immunity regarding disturbances. When a connexion is lost in the chain all the projectors after the losy connection are

Marantz PM350 : How to repair a vintage amp
Introduction A guy bring to me a MARANTZ PM350 amplifier. He says that to have a little sound the volume button has to be set to the maximum. And, it only works on left channel. The PM350 is a vintage (1980) audio amplifier designed by MARANTZ. I used it several years and the sound is

Reparation d’un Marantz PM350
Need English version? It’s here Introduction L’autre jour quelqu’un m’a apporté un amplificateur Marantz PM350. Le son était tout faible même avec le volume tourné à fond. En plus, seulement la voie de gauche fonctionne. Alors il faut savoir que le PM350 est un ampli qui date des années 80 de type AB. J’en avait

Mic to line amplifier
Introduction So I needed to connect a standard microphone to a conventional speaker amplifier. The signal comming out the mic is really low. It can be lower than 20mV. You need to amplify the signal to the line level. That’s why with the component I have in stock I do this simple microphone pre-amplifier. The

Amplificateur de microphone vers niveau ligne
Introduction J’avais besoin de connecter un microphone standard à un amplificateur audio sur une entrée ligne. Le signal qui provient du microphone est très faible avec quelques 20mV. Il faut donc amplifier le signal du microphone pour avoir un signal de niveau ligne. Cet article vous présente le Pré-ampli de microphone DIY avec les composants

Getting DMX data in a PIC
Introduction When I need to change the functions of a fixture I use the DMX bus to drive them. This article presents you the software code I use (in C language) to decode the data. I’m using it on PIC MCU from Microchip. It may be possible to adapt the code for other hardware. DMX

Réalisation d’un répéteur DMX isolé
Need english version? Click here Lire la suiteDéveloppement d’un Blinder LED DMX Introduction Quand on veut connecter des projecteurs DMX entre eux, on peut soit utiliser le sans fil soit des câbles. Dans mon cas, l’installation étant fixe, on a privilégié les câbles. Un des défauts du DMX câblé c’est sa fragilité. Si l’une

Réparation d’un LUMISKY Lucy Play
Introduction Dernière réparation, un LUMISKY Lucy Play qui a été branché en 12V au lieu des 5V. Du coup, le régulateur de charge de la batterie Li-Ion a chauffé et a cassé. Un remplacement du TP4056 permet de récupérer la charge de la batterie. Mais ce n’est pas le seul problème. Quand on appuie sur
Archives
Calendar
L | M | M | J | V | S | D |
---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | 5 | 6 | |
7 | 8 | 9 | 10 | 11 | 12 | 13 |
14 | 15 | 16 | 17 | 18 | 19 | 20 |
21 | 22 | 23 | 24 | 25 | 26 | 27 |
28 | 29 | 30 | 31 |